EN1xN光开关
1XN机械式光开关 产品名称： 1XN机械式光开关产品特征：低插入损耗 波长范围宽低串扰高稳定性和可靠性并行接口(TTL电平)控制模块化设计2<N48 应用范围：Ø 实验室研发Ø 系统监测Ø 配置OADMØ 城域网Ø 器件测试Ø 光纤传感器Ø 光纤环路Ø 多路光监测Ø 光纤传感Ø 远程光纤监控系统 技术参数型号HTD-FSW-1N波长范围nm532~980(SM/MM)670~980(S
1XN机械式光开关 产品名称： 1XN机械式光开关产品特征：低插入损耗 波长范围宽低串扰高稳定性和可靠性并行接口(TTL电平)控制模块化设计2<N48 应用范围：Ø 实验室研发Ø 系统监测Ø 配置OADMØ 城域网Ø 器件测试Ø 光纤传感器Ø 光纤环路Ø 多路光监测Ø 光纤传感Ø 远程光纤监控系统 技术参数型号HTD-FSW-1N波长范围nm532~980(SM/MM)670~980(S
1XN机械式光开关
产品名称： 1XN机械式光开关
产品特征：
低插入损耗
波长范围宽
低串扰
高稳定性和可靠性
并行接口(TTL电平)控制
模块化设计
2<N≤48
应用范围：
Ø 实验室研发
Ø 系统监测
Ø 配置OADM
Ø 城域网
Ø 器件测试
Ø 光纤传感器
Ø 光纤环路
Ø 多路光监测
Ø 光纤传感
Ø 远程光纤监控系统
技术参数
型号 | HTD-FSW-1×N | |||
波长范围nm | 532~980(SM/MM) | 670~980(SM/MM) | 1250~1650（MM） | 1250~1650（SM） |
测试波长nm | 532/785/850/980 | 670/785/850/980 | 1310/1490/1550/1625 | 1310/1490/1550/1625 |
插入损耗dB | Typ:1.0 Max:1.6 | Typ:0.6 Max:1.2 | Typ:0.6 Max:0.8 | Typ:0.5 Max:0.8 |
回波损耗dB | SM≥50、MM≥30 | |||
信道串扰dB | SM≥55、MM≥35 | |||
偏振相关损耗dB | ≤0.05 | |||
波长相关损耗dB | ≤0.25 | |||
温度相关损耗 dB | ≤0.25 | |||
重复性 dB | ≤±0.02 | |||
工作电压V | +5 or +12 | |||
使用寿命次 | ≥108 | |||
切换时间ms | ≤8（相邻信道切换） | |||
传输光功率mW | ≤500 | |||
工作温度℃ | -20～+70 | |||
储存温度℃ | -40～+85 | |||
外形尺寸mm | 2<N<6 (135×40×32) 6≤N≤12 (135×64×32) 8≤N≤16(184×78×38) 16≤N≤48(184×78×66) | |||
注:1.以上为不含连接头指标；2.可根据要求定做特殊规格产品。
管脚定义
DB25针
Pin Number | Signal Direction | Name | Function |
15 | in | D0 | Data bits D0 to D6: used to select ports, for example: 0000000b=port 1, 0000001b=port 2; D0 is LSB and D6 is MSB. |
16 | in | D1 | |
17 | in | D2 | |
18 | in | D3 | |
19 | in | D4 | |
20 | in | D5 | |
21 | in | D6 | |
22 | in | /RESET | Reset signal: a low-level forces the switch to move to an open position; a high-level allows the switch to move to the position specified by the data lines. |
2 | out | /READY | Ready status signal: Low means ready to reset or switch to the position specified by the data lines, high means internal operation. |
3 | out | ERROR | Error status signal: high-level indicates an internal error has occurred. |
12,25 | Power in | 5V | Logic supply |
13 | Power in | 5V/12V | Driver supply |
1,10,14,23 | Power | Ground | Ground |
24 | Not connected | Not connected | |
4,5,6,7,8,9,11, 20,21 | Not connected | Not connected |
DB15针
Pin Number | Signal Direction | Name | Function |
2 | in | D0 | Data bits D0 to D4: used to select ports 0 through 16(binary), for example: 00000b=port 1, 11111b=port 16; D0 is LSB and D4 is MSB. |
3 | in | D1 | |
4 | in | D2 | |
5 | in | D3 | |
6 | in | D4 | |
11 | in | /RESET | Reset signal: a low-level forces the switch to move to an open position; a high-level allows the switch to move to the position specified by the data lines. |
7 | out | /READY | Ready status signal: Low means ready to reset or switch to the position specified by the data lines, high means internal operation. |
8 | out | ERROR | Error status signal: high-level indicates an internal error has occurred. |
15 | Power in | 5V | Logic supply |
12 | Power in | 5V/12V | Driver supply |
1,9 | Power | Ground | Ground |
10,13,14 | Not connected | Not connected |
DB9针
Pin Number | Signal Direction | Name | Function |
1 |
in |
D0 | Data bits D0 to D3: used to select ports 0 through 16 (binary),for example:0000b=port1, 1111b= port16; D0 is LSB and D3 is MSB. |
2 | in | D1 | |
3 | in | D2 | |
4 | in | D3 | |
5 |
in |
/RESET | Reset signal: a low-level forces the switch to move to an open position; a high-level allows the switch to move to the position specified by the data lines. |
6 | out | /READY | Ready status signal: Low means ready to reset or switch to the position specified by the data lines, high means internal operation. |
7 |
out |
ERROR | Error status signal: high-level indicates an internal error has occurred. |
8 | Power | GROUND | Ground |
9 | Power in | 5V | Power supply |
订购信息：
FSW | -1XN | |||||
光开关 | 通道数 | 工作波长 | 光纤规格 | 光纤外径 | 出纤长度 | 连接头 |
N=2-48 | 85=850 98=980 13=1310 15=1550 35=1310&1550 00=其它 | SM=SMF-28E M5=MM50/125 M6=MM62.5/125 S=客户指定 | 01=裸光纤 09=Ø0.9松套管 90=Ø0.9紧套管 20=Ø2.0光纤 30=Ø3.0光纤 | 0=0.5米 1=1米 2=2米 S=客户指定 | NA=无连接头 FP=FC/PC FA=FC/APC SP=SC/PC SA=SC/APC LP=LC/UPC LA=LC/APC MU=MU/UPC S=客户指定 |